Sandblasting, Industrial Painting and Powder Coating
Parts leave us blasted and coated to the system on your drawing, ready to assemble. Sandblasting to Sa 2½, wet paint systems to ISO 12944 and powder coating in the colour you specify, with dry film thickness measured before packing.
- Sa 2½Blast cleaning, ISO 8501-1
- C1–C5Corrosivity classes, ISO 12944
- RALAny colour you specify
- DFTMeasured before packing
- PowderCoating for frames and parts
Finished, Coated and Ready to Assemble
A coating is only as good as the surface under it. Welded frames, structures and machined parts are sandblasted to remove mill scale, rust and weld spatter, then coated within the time window the paint system allows. Machined faces, threads and bores are masked so they arrive clean.
You tell us the paint system, colour and corrosivity class, or we propose one for the environment the part will see. Wet paint, powder coating and galvanizing can all be ordered with the part, so you buy one finished component instead of managing a fabricator and a coater.
Finishing at a glance
- BlastingSa 2½ to ISO 8501-1
- Wet paintPrimer, intermediate, top coat
- Powder coatingRAL colours, textures
- CorrosivityC1–C5 to ISO 12944
- MaskingMachined faces, threads, bores
- ChecksDFT to ISO 2808, adhesion on request
Coating Options
Sandblasting
Blast cleaning of frames, structures and series parts to the grade your coating system needs.
- Sa 2½ standard, Sa 3 on request
- Weld and edge preparation
- Roughness for paint adhesion
Industrial Painting
Multi-coat paint systems for machinery, structures and outdoor equipment, to your specification.
- Epoxy, polyurethane, zinc-rich primers
- ISO 12944 systems C1–C5
- Any RAL colour
Powder Coating
A hard, even finish for frames, brackets, housings and covers, especially in series.
- RAL colours and textures
- Uniform film on repeat parts
- Duplex over galvanizing on request
What to Put on the Drawing
Give us the system or the environment, and we confirm it on the quotation.
| Item | Example | Standard |
|---|---|---|
| Surface preparation | Sa 2½, medium grit | ISO 8501-1, ISO 8503 |
| Corrosivity and durability | C4 high (H) | ISO 12944-2, -5 |
| Paint system | Epoxy primer + PU top coat, 240 µm | ISO 12944-5 |
| Colour | RAL 5010, gloss or matt | RAL |
| Masking | Machined faces, threads, bores | Drawing |
| Inspection | DFT readings, adhesion test | ISO 2808, ISO 2409 |
Finishing in Practice
Questions About Sandblasting and Painting
Do you sandblast and paint the parts you fabricate?
Yes. Parts are sandblasted and painted or powder coated to your specification before inspection and packing.
Which paint systems do you apply?
Epoxy, polyurethane and zinc-rich systems to ISO 12944, in any RAL colour. Send your system or tell us the environment and corrosivity class.
Do you offer powder coating?
Yes, in RAL colours and textures. It suits frames, brackets, housings and covers, especially in series.
Do you measure coating thickness?
Yes. Dry film thickness is measured before packing, and a coating report can be supplied with the order.
Can machined faces be protected?
Yes. Machined faces, threads and bores are masked during blasting and painting and protected for transport.
Sandblasting and Industrial Coating in Türkiye
For a European buyer, the most expensive coating problem is one found at assembly. Parts that arrive with thin paint on edges, overspray on bearing seats or rust bleeding from a weld seam cost time on the line. Our finishing process is set up to avoid that: blasting to the right grade, edges and welds prepared, machined faces masked, and film thickness measured.
Blasting to the right grade
Most paint systems need Sa 2½ to ISO 8501-1 and a defined roughness profile. Welded frames are blasted after fabrication, so weld spatter and heat tint are removed together with mill scale.
Paint systems to ISO 12944
We apply primer, intermediate and top coats to the system on your drawing, from indoor machinery (C2) to outdoor and coastal equipment (C4, C5). Powder coating gives a uniform finish on repeat parts. For maximum protection, parts can be hot-dip galvanized and then painted as a duplex system.
Part of one order
Finishing follows welding and machining on the same quotation, and coated parts go through inspection and export packing before shipment. Send your drawing with the coating requirement.
Send a drawing with your coating spec.
Include the paint system or corrosivity class, colour and masking. We reply with feasibility, lead time and price.